Hello i just bought a virtual boy from the flea market for 80 bucks plus 4 games and i noticed that the left eye display does not work,is there anything hat i can do to fix it ? or is there a repair service that can fix it for me ? i dont know how to open it nor do i know how to really sotter things.

Yankeesfan239 wrote:
Hello i just bought a virtual boy from the flea market for 80 bucks plus 4 games and i noticed that the left eye display does not work,is there anything hat i can do to fix it ? or is there a repair service that can fix it for me ? i dont know how to open it nor do i know how to really sotter things.

Hello dear friend, I had the same problem with my VR, and what arrangements with the oven method, which you must uncover the VR …

Sorry..my English is not good I am Chile but I am very happy to regain my virtual boy.

you leave the Link

http://www.vr32.de/modules/newbb/viewtopic.php?topic_id=3295&forum=1

good luck my friend 🙂 🙂 🙂 :thumpup: :thumpup: 😉 😉

where can i buy the tool already made ? also i dont know much about working with the boards,and stuff. is here a repair service that can do it in case i cant figure it out ? i know intendo dont do that anymore lol.

Yankeesfan239 wrote:
where can i buy the tool already made ?

This is the tool you need: http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=380046336230

[dasi]

It appears the bit linked to above isn’t long enough for the two deep screws. You have been warned.

• This reply was modified 15 years, 9 months ago by dasi.

ok thank you is there like a vid or pics on how to sotter the wires using the 30 gauge kynars shown in the bypass guide,i see how he did it but i just dont know where any of the wires really go and stuff i am not really sottering expert.

ok how long would the tool need to be to be able to reach all of the screws ? where can i get the longest one that will work ? i wanna play theis so badly lol.

anyone know ? is there a way to use that bit and make it longer?

Yes, you can grind/file down the thick part of it and make a notch in the end to fit a normal screwdriver there. That’s what I and many others have done.

The holes are approximately 45 mm deep. The bit above is only 40 mm long. To make it long enough you’d need to modify it.

Edit: beaten 😛

ok cool i dont know if i would be good at that,but do you ugys think these ones would work ? what is the correct bit size,can you look at my links and tel me if this is what i need?

here is the bit driver: http://electricquarter.com/tool-magentic-driver-p-58.html?osCsid=358f51c31dfa411e5ace897fda018bf1

here is the bit: http://www.mcmelectronics.com/product/22-1150

ok i got the tool,got it open the screws were tight,and on the left display chip i dont see the red blinking ights that i should see and i am messing with the cable,and theres no intermittment display on it,i dont know if the cable is damaged or not its small,what shouodl i do now?

Yankeesfan239 wrote:
ok cool i dont know if i would be good at that,but do you ugys think these ones would work ? what is the correct bit size,can you look at my links and tel me if this is what i need?

here is the bit driver: http://electricquarter.com/tool-magentic-driver-p-58.html?osCsid=358f51c31dfa411e5ace897fda018bf1

here is the bit: http://www.mcmelectronics.com/product/22-1150

Hello!!

Regarding the size of the screwdriver. It should be about 8 CM (only the iron without the magician).

It is possible that some mangoes should be spent, so that the iron has a long 8 CM.

Ya que algunos tornillos son muy profundos.

I am presenting my screwdriver purchased at a store in Chile

http://img67.imageshack.us/my.php?image=mvc002sfn9.jpg%5D[/URL]

http://img67.imageshack.us/my.php?image=mvc003sdr0.jpg%5D[/URL]

http://img523.imageshack.us/my.php?image=mvc005sce4.jpg%5D[/URL]

http://img67.imageshack.us/my.php?image=mvc006sis9.jpg%5D[/URL]

http://img523.imageshack.us/my.php?image=mvc010snv7.jpg%5D[/URL]

I hope I helped, greetings. 😉 😉 😉